1. All ferrous parts are hot dip galvanized to ASTM A153 / BS 729

NOTE:
Other sizes available on request
All dimensions in mm / inches * We reserve the right to change design & construction without prior notice

1. Pole top brackets are used with post insulator with stud or short shank insulator pin mounted with 5/8 inch dia bolts
2. Pole top brackets are suitable for vertical mounting
3. All ferrous parts are hot dip galvanized to ASTM A153

NOTE:
Other sizes available on request
All dimensions in mm / inches * We reserve the right to change design & construction without prior notice

1. Please add length ( l ) to the suffix while ordering.
2. Thread length will be supplied standard unless otherwise specified while ordering
3. Carriage bolts supplied complete with one square nut unless otherwise specified
4. All ferrous parts hot dip galvanized to ASTM A153
5. Carriage bolts and nuts confirm to ANSI C135.1

NOTE:
Other sizes available on request
All dimensions in mm / inches * We reserve the right to change design & construction without prior notice

1. Eye nuts are single piece forged construction
2. Eye nuts are tapped oversize ( 0.015 ) as permitted after galvanizing to ensure smooth fitment with matching threads on bolts
3. All ferrous parts are hot dip galvanized to ASTM A153 and internal threads oiled
   after re tapping to prevent rusting as permitted by specification

NOTE:
Other sizes available on request
All dimensions in mm / inches * We reserve the right to change design & construction without prior notice

Nuts may be hex or square And to be specified while ordering

Threads cut or rolled and to be specified while ordering

1. Anchors rods supplied with one square nut unless otherwise specified
2. Washer can be supplied at additional cost.
3. Recommended size of washer is as stated above.
4. All ferrous parts hot dip galvanized to ASTM A153
5. Twin eye anchor rods conform to requirements of ANSI C135.2

NOTE:
Other sizes available on request
All dimensions in mm / inches * We reserve the right to change design & construction without prior notice

Rolled Threads

1. Square bolts supplied complete with one square nut unless otherwise specified
2. Washers ( round and spring ) can be supplied if specified at additional cost
3. All ferrous parts hot dip galvanized to ASTM A153
4. Square bolts and nuts confirm to requirement of ANSI C135.1

NOTE:
Other sizes available on request
All dimensions in mm / inches * We reserve the right to change design & construction without prior notice

1. Braces available in straight / twisted types of varying sizes
2. All ferrous parts hot dip galvanized to ASTM A153 / BS 729

NOTE:
Other sizes available on request
All dimensions in mm / inches * We reserve the right to change design & construction without prior notice

Forged Eye
Cut / rolled threads
Semi Cone Points

1. B = 4 ( IF A =< 10 )
2. B = 6 ( IF A > 10 )
3. Please specify l1 when ordering by adding required length to the suffix of the catalog number
4. Oval eye bolts supplied complete with one nut ( hex / square ) unless otherwise specified
5. Washers ( round / spring ) can be supplied at additional cost
6. All ferrous parts are hot dip galvanized to ASTM A153
7. Oval eye bolts conforms to requirements of ANSI C135.4

NOTE:
Other sizes available on request
All dimensions in mm / inches * We reserve the right to change design & construction without prior notice

Nuts may be hex or square And to be specified while ordering
Threads cut or rolled and to be specified while ordering

1. Anchor rods supplied with one square nut unless otherwise specified
2. Washer can be supplied at additional cost.
3. Recommended size of washer is as stated above.
4. All ferrous parts hot dip galvanized to ASTM A153
5. Thimble eye anchor rods conform to requirements of ANSI C135.2

NOTE:
Other sizes available on request
All dimensions in mm / inches * We reserve the right to change design & construction without prior notice

li>Stay tightner consist of a body and two end fittings which can be eye type, hook type, clevis type or in various shaped as required by buyer
1. The body and end fittings are single piece forged construction
2. Locks nuts can also be supplied to supplement tightening if ordered
3. Thimble can also be supplied if ordered separately
4. All ferrous parts are hot dip galvanized to ASTM A153 / BS 729

NOTE:
Other sizes available on request
All dimensions in mm / inches * We reserve the right to change design & construction without prior notice